The AD8018 is intended for use in single-supply (5 V) xDSL modems where high-output current and low distortion are essential to achieve maximum reach. The dual high-speed amplifiers are capable of driving low distortion signals to within 0.5 V of the power supply rail. Each amplifier can drive 400 mA of current into 10 (differential) while maintaining 82 dBc out-of-band SFDR. The AD8018 is available with flexible standby and shutdown modes. Two digital logic bits (PWDN1 and PWDN0) may be used to put the AD8018 into one of three modes: full power, standby (outputs low impedance), and shutdown (outputs high impedance).
Fabricated with ADI's high-speed XFCB (eXtra Fast Complementary Bipolar) process, the high bandwidth and fast slew rate of the AD8018 keep distortion to a minimum, while dissipating a minimum of power. The quiescent current of the AD8018 is a low 9 mA/amplifier. The AD8018 drive capability comes in compact 8-lead Thermal Coastline SOIC and 14-lead TSSOP packages. Low-distortion, rail-to-rail output voltage, and highcurrent drive in small packages make the AD8018 ideal for use in low-cost USB, PCMCIA, and PCI Customer Premise Equipment for ADSL, SDSL, VDSL, and proprietary xDSL systems. Both models will operate over the temperature range 40°C to
+85°C.
|
|
|
xDSL USB, PCI, PCMCIA CardsConsumer DSL ModemsTwisted Pair Line Driver
|
Ideal xDSL Line Drive Amplifier for USB, PCMCIA, or PCI-Based Customer Premise Equipment (CPE). The AD8018 provides maximum reach on 5 V supply, driving 16 dBm of power into a back-terminated, transformer-coupled 100 while maintaining 82 dBc of out-of-band SFDR.Rail-to-Rail Output Voltage and High Output Current Drive.400 mA Output Current into Differential Load of 10 @ 8 V p-pLow Single-Tone Distortion86 dBc Worst Harmonic, 6 V p-p into Differential 10 @ 100 kHzLow Noise4.5 nV/Hz Voltage Noise Density, 100 kHzOut-of-Band SFDR = 82 dBc, 144 kHz to 500 kHz, RLOAD = 12.5 , PLINE = 13 dBmLow-Power Operation3.3 V to 8 V Power Supply Range Two Logic Bits for Standby and Shutdown Low Supply Current of 9 mA/Amplifier (Typ)Current Feedback AmplifiersHigh Speed 130 MHz Bandwidth (3 dB) 300 V/s Slew Rate
|
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V
Internal Power Dissipation2
Small Outline Package (R) . . . . . . . . . . . . . . . . . . . .......650 mW
TSSOP Package (RU) . . . . . . . . . . . . . . . . . . . . . .......... 565 mW
Input Voltage (Common-Mode) . . . . . . . . . . . . . . . . . . . .... ±VS
Logic Voltage, PWDN0, 1 . . . . . . . . . . . . . . . . . . . . . . . . ... ±VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . .±1.6 V
Output Short Circuit Duration
. . . . . . . . . . . . . . . . . . . . . . .....Observe Power Derating Curves
Storage Temperature Range RU, R . . . . . . . 65°C to +125°C
Operating Temperature Range . . . . . . . . . . . 40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . . 300°C
Post a Buying Lead
Required Field 
